forked from Ivasoft/openwrt
b56bcfe3be
This adds support for the Ubiquiti Nanostation Loco M (XM), which has the same board/LEDs as the Bullet M XM, but different case and antennas. Specifications: - AR7241 SoC @ 400 MHz - 32 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - NS Loco M2: built-in antenna: 8 dBi; AR9287 - NS Loco M5: built-in antenna: 13 dBi; 2T2R 5 GHz radio - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via WebUI: Upload the factory image via the stock firmware web UI. Note that only certain firmware versions accept unsigned images. Refer to the device's Wiki page for further information. Flashing via TFTP: Same procedure as other NanoStation M boards. - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-squashfs-factory.bin Tested on NanoStation Loco M2. Signed-off-by: Sven Roederer <freifunk@it-solutions.geroedel.de> Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
151 lines
3.4 KiB
Bash
151 lines
3.4 KiB
Bash
#!/bin/sh
|
|
|
|
[ -e /lib/firmware/$FIRMWARE ] && exit 0
|
|
|
|
. /lib/functions/caldata.sh
|
|
. /lib/functions/mikrotik-caldata.sh
|
|
|
|
board=$(board_name)
|
|
|
|
case "$FIRMWARE" in
|
|
"ath9k-eeprom-ahb-18100000.wmac.bin")
|
|
case $board in
|
|
avm,fritz4020)
|
|
caldata_extract_reverse "urlader" 0x1541 0x440
|
|
;;
|
|
dlink,dir-505|\
|
|
dlink,dir-825-c1|\
|
|
dlink,dir-835-a1)
|
|
caldata_extract "art" 0x1000 0x440
|
|
ath9k_patch_mac $(mtd_get_mac_text "mac" 0x4)
|
|
;;
|
|
dlink,dir-842-c1|\
|
|
dlink,dir-842-c2|\
|
|
dlink,dir-842-c3|\
|
|
dlink,dir-859-a1|\
|
|
nec,wg1200cr|\
|
|
wd,mynet-n750)
|
|
caldata_extract "art" 0x1000 0x440
|
|
ath9k_patch_mac $(mtd_get_mac_ascii devdata "wlan24mac")
|
|
;;
|
|
engenius,ecb1750)
|
|
caldata_extract "art" 0x1000 0x440
|
|
ath9k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env "athaddr") +1)
|
|
;;
|
|
engenius,epg5000|\
|
|
iodata,wn-ac1167dgr|\
|
|
iodata,wn-ac1600dgr|\
|
|
iodata,wn-ac1600dgr2|\
|
|
iodata,wn-ag300dgr|\
|
|
sitecom,wlr-7100)
|
|
caldata_extract "art" 0x1000 0x440
|
|
ath9k_patch_mac $(mtd_get_mac_ascii u-boot-env ethaddr)
|
|
;;
|
|
mikrotik,routerboard-wap-g-5hact2hnd)
|
|
mikrotik_caldata_extract "art" 0x1000 0x440
|
|
ath9k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x10) +2)
|
|
;;
|
|
nec,wg800hp)
|
|
caldata_extract "art" 0x1000 0x440
|
|
ath9k_patch_mac $(mtd_get_mac_text board_data 0x680)
|
|
;;
|
|
qihoo,c301)
|
|
caldata_extract "radiocfg" 0x1000 0x440
|
|
ath9k_patch_mac $(mtd_get_mac_ascii devdata "wlan24mac")
|
|
;;
|
|
*)
|
|
caldata_die "board $board is not supported yet"
|
|
;;
|
|
esac
|
|
;;
|
|
"ath9k-eeprom-pci-0000:00:00.0.bin")
|
|
case $board in
|
|
avm,fritz300e)
|
|
caldata_extract_reverse "urloader" 0x1541 0x440
|
|
;;
|
|
buffalo,wzr-hp-g302h-a1a0)
|
|
caldata_extract "art" 0x1000 0xeb8
|
|
;;
|
|
buffalo,wzr-hp-g450h)
|
|
caldata_extract "art" 0x1000 0x440
|
|
;;
|
|
dlink,dir-825-c1|\
|
|
dlink,dir-835-a1)
|
|
caldata_extract "art" 0x5000 0x440
|
|
ath9k_patch_mac $(macaddr_add $(mtd_get_mac_text "mac" 0x18) 1)
|
|
;;
|
|
ocedo,raccoon|\
|
|
tplink,tl-wdr3500-v1|\
|
|
tplink,tl-wdr3600-v1|\
|
|
tplink,tl-wdr4300-v1|\
|
|
tplink,tl-wdr4300-v1-il|\
|
|
tplink,tl-wdr4900-v2|\
|
|
winchannel,wb2000)
|
|
caldata_extract "art" 0x5000 0x440
|
|
;;
|
|
netgear,wnr2200-8m|\
|
|
netgear,wnr2200-16m|\
|
|
pcs,cap324|\
|
|
tplink,tl-wr2543-v1|\
|
|
tplink,tl-wr842n-v1|\
|
|
ubnt,airrouter|\
|
|
ubnt,bullet-m|\
|
|
ubnt,nanostation-loco-m|\
|
|
ubnt,nanostation-m|\
|
|
ubnt,rocket-m)
|
|
caldata_extract "art" 0x1000 0x1000
|
|
;;
|
|
ubnt,unifi)
|
|
caldata_extract "art" 0x1000 0x800
|
|
;;
|
|
wd,mynet-n750)
|
|
caldata_extract "art" 0x5000 0x440
|
|
ath9k_patch_mac $(mtd_get_mac_ascii devdata "wlan5mac")
|
|
;;
|
|
wd,mynet-wifi-rangeextender)
|
|
caldata_extract "art" 0x1000 0x1000
|
|
ath9k_patch_mac $(nvram get wl0_hwaddr)
|
|
;;
|
|
*)
|
|
caldata_die "board $board is not supported yet"
|
|
;;
|
|
esac
|
|
;;
|
|
"ath9k-eeprom-pci-0000:00:11.0.bin")
|
|
case $board in
|
|
buffalo,wzr-hp-ag300h|\
|
|
netgear,wndr3700|\
|
|
netgear,wndr3700-v2|\
|
|
netgear,wndr3800|\
|
|
netgear,wndr3800ch)
|
|
caldata_extract "art" 0x1000 0xeb8
|
|
;;
|
|
dlink,dir-825-b1)
|
|
caldata_extract "caldata" 0x1000 0xeb8
|
|
ath9k_patch_mac_crc $(mtd_get_mac_text "caldata" 0xffa0) 0x20c
|
|
;;
|
|
*)
|
|
caldata_die "board $board is not supported yet"
|
|
;;
|
|
esac
|
|
;;
|
|
"ath9k-eeprom-pci-0000:00:12.0.bin")
|
|
case $board in
|
|
buffalo,wzr-hp-ag300h|\
|
|
netgear,wndr3700|\
|
|
netgear,wndr3700-v2|\
|
|
netgear,wndr3800|\
|
|
netgear,wndr3800ch)
|
|
caldata_extract "art" 0x5000 0xeb8
|
|
;;
|
|
dlink,dir-825-b1)
|
|
caldata_extract "caldata" 0x5000 0xeb8
|
|
ath9k_patch_mac_crc $(macaddr_add $(mtd_get_mac_text "caldata" 0xffb4) 1) 0x20c
|
|
;;
|
|
*)
|
|
caldata_die "board $board is not supported yet"
|
|
;;
|
|
esac
|
|
;;
|
|
esac
|