forked from Ivasoft/openwrt
86e18f6706
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
- 802.3af POE on Ethernet 1
- 18-24v passive POE (mode B) on Ethernet 2
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
58 lines
1015 B
Bash
58 lines
1015 B
Bash
PART_NAME=firmware
|
|
REQUIRE_IMAGE_METADATA=1
|
|
|
|
RAMFS_COPY_BIN='fw_printenv fw_setenv'
|
|
RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
|
|
|
|
platform_check_image() {
|
|
return 0;
|
|
}
|
|
|
|
platform_do_upgrade() {
|
|
case "$(board_name)" in
|
|
linksys,ea8500)
|
|
platform_do_upgrade_linksys "$ARGV"
|
|
;;
|
|
netgear,d7800 |\
|
|
netgear,r7500 |\
|
|
netgear,r7500v2 |\
|
|
netgear,r7800 |\
|
|
qcom,ap-dk04.1-c1 |\
|
|
qcom,ipq8064-ap148 |\
|
|
zyxel,nbg6817)
|
|
nand_do_upgrade "$ARGV"
|
|
;;
|
|
openmesh,a42)
|
|
PART_NAME="inactive"
|
|
platform_do_upgrade_openmesh "$ARGV"
|
|
;;
|
|
tplink,c2600)
|
|
PART_NAME="os-image:rootfs"
|
|
MTD_CONFIG_ARGS="-s 0x200000"
|
|
default_do_upgrade "$ARGV"
|
|
;;
|
|
tplink,vr2600v)
|
|
PART_NAME="kernel:rootfs"
|
|
MTD_CONFIG_ARGS="-s 0x200000"
|
|
default_do_upgrade "$ARGV"
|
|
;;
|
|
*)
|
|
default_do_upgrade "$ARGV"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
platform_nand_pre_upgrade() {
|
|
case "$(board_name)" in
|
|
zyxel,nbg6817)
|
|
zyxel_do_upgrade "$1"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
blink_led() {
|
|
. /etc/diag.sh; set_state upgrade
|
|
}
|
|
|
|
append sysupgrade_pre_upgrade blink_led
|