forked from Ivasoft/openwrt
52b59a984f
Head Weblink HDRM200 is a dual-sim router based on MT7620A. The detailed specifications are: - MT7620A (580MHz) - 64MB RAM - 16MB of flash (SPI NOR) - 6x 10/100Mbps Ethernet (MT7620A built-in switch) - 1x microSD slot - 1x miniPCIe slot (only USB2.0 bus). Device is shipped with a SIMCOM SIM7100E LTE modem. - 2x SIM slots (standard size) - 1x USB2.0 port - 1x 2.4GHz wifi (rt2800) - 1x 5GHz wifi (mt7612) - 1x reset button - 1x WPS button - 3x GPIO-controllable LEDs - 1x 10 pin terminal block (RS232, RS485, 4 x GPIO) Tested: - Ethernet switch - Wifi - USB slot - SD card slot - miniPCIe-slot - sysupgrade - reset button Installation instructions: Installing OpenWRT for the first time requires a bit of work, as the board does not ship with OpenWRT. In addition, the bootloader automatically reboots when installing an image over tftp. In order to install OpenWRT on the HDRM200, you need to do the following: * Copy the initramfs-image to your tftp-root (default filename is test.bin) and configure networking accordingly (default server IP is 10.10.10.3, client 10.10.10.123). Start your tftp server. * Open the board and connect to UART. The pins are exposed and clearly marked. * Boot the board and press 1. * Either use the default filename and client/server IP-addresses, or specify your own. The image should now be loaded to memory and board boot. If the router reboots while the image is loading, you need to try again. Once the board has booted, copy the sysupgrade-image to the router and run sysupgrade in order to install OpenWRT to the flash. Notes: - You control which SIM slot to use by writing 0/1 to /sys/class/gpio/gpio0/value. In order for the change to take effect, you can either use AT-commands (AT+CFUN) or power-cycle the modem (write 0/1 to /sys/class/gpio/gpio21/value). - RS485 is available on /dev/ttyS0. - RS232 is available on /dev/ttyS1. - The name of the ioX-gpios map to the labels on the casing. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> [fixed whitespace issue and merge conflict in target.mk] Signed-off-by: Petr Štetiar <ynezz@true.cz>
691 lines
14 KiB
Bash
Executable File
691 lines
14 KiB
Bash
Executable File
#!/bin/sh
|
|
|
|
. /lib/functions.sh
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/system.sh
|
|
|
|
ramips_setup_rt3x5x_vlans()
|
|
{
|
|
if [ ! -x /sbin/swconfig ]; then
|
|
# legacy default
|
|
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
|
|
return
|
|
fi
|
|
local wanports=""
|
|
local lanports=""
|
|
for port in 5 4 3 2 1 0; do
|
|
if [ `swconfig dev rt305x port $port get disable` = "1" ]; then
|
|
continue
|
|
fi
|
|
if [ `swconfig dev rt305x port $port get lan` = "0" ]; then
|
|
wanports="$port:wan $wanports"
|
|
else
|
|
lanports="$port:lan $lanports"
|
|
fi
|
|
done
|
|
ucidef_add_switch "rt305x" $lanports $wanports "6t@eth0"
|
|
}
|
|
|
|
ramips_setup_interfaces()
|
|
{
|
|
local board="$1"
|
|
|
|
case $board in
|
|
11acnas|\
|
|
d-team,newifi-d2|\
|
|
dir-615-h1|\
|
|
w2914nsv2|\
|
|
zbt-we2026)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "4:wan:5" "6@eth0"
|
|
;;
|
|
3g150b|\
|
|
3g300m|\
|
|
a5-v11|\
|
|
all0256n-4M|\
|
|
all0256n-8M|\
|
|
all5002|\
|
|
all5003|\
|
|
bocco|\
|
|
broadway|\
|
|
dcs-930|\
|
|
dcs-930l-b1|\
|
|
ht-tm02|\
|
|
kimax,u35wf|\
|
|
linkits7688 | \
|
|
m2m|\
|
|
microwrt|\
|
|
mikrotik,rbm11g|\
|
|
mpr-a2|\
|
|
ncs601w|\
|
|
omega2 | \
|
|
omega2p | \
|
|
timecloud|\
|
|
tplink,tl-wa801nd-v5|\
|
|
w150m|\
|
|
widora,neo-16m|\
|
|
widora,neo-32m|\
|
|
wnce2001|\
|
|
zbt-cpe102|\
|
|
zorlik,zl5900v2|\
|
|
zte-q7)
|
|
ucidef_add_switch "switch0"
|
|
ucidef_add_switch_attr "switch0" "enable" "false"
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
mlw221|\
|
|
mr-102n)
|
|
ucidef_set_interface_lan "eth0.2"
|
|
;;
|
|
3g-6200n|\
|
|
ai-br100|\
|
|
alfa-network,ac1200rm|\
|
|
mediatek,ap-mt7621a-v60|\
|
|
xzwifi,creativebox-v1|\
|
|
d240|\
|
|
db-wrt01|\
|
|
dir-300-b7|\
|
|
dir-320-b1|\
|
|
dir-610-a1|\
|
|
dir-615-h1|\
|
|
dir-810l|\
|
|
dlink,dwr-116-a1|\
|
|
dlink,dwr-921-c1|\
|
|
dlink,dwr-922-e2|\
|
|
ew1200|\
|
|
firewrt|\
|
|
hc5661a|\
|
|
hc5962|\
|
|
hlk-rm04|\
|
|
k2p|\
|
|
kn|\
|
|
kn_rc|\
|
|
mac1200rv2|\
|
|
miwifi-mini|\
|
|
miwifi-nano|\
|
|
mt7621|\
|
|
mt7628|\
|
|
mtc,wr1201|\
|
|
mzk-750dhp|\
|
|
mzk-w300nh2|\
|
|
nixcore-x1-8M|\
|
|
nixcore-x1-16M|\
|
|
oy-0001|\
|
|
pbr-m1|\
|
|
psg1208|\
|
|
psg1218a|\
|
|
r6220|\
|
|
netgear,r6350|\
|
|
rt-n12p|\
|
|
sap-g3200u3|\
|
|
sk-wb8|\
|
|
unielec,u7621-06-256m-16m|\
|
|
unielec,u7621-06-512m-64m|\
|
|
vr500|\
|
|
wavlink,wl-wn570ha1|\
|
|
wavlink,wl-wn575a3|\
|
|
wf-2881|\
|
|
whr-g300n|\
|
|
mqmaker,witi-256m|\
|
|
mqmaker,witi-512m|\
|
|
wndr3700v5|\
|
|
youku-yk1|\
|
|
youku,yk-l2|\
|
|
zbt-ape522ii|\
|
|
zbt-we1326|\
|
|
zbtlink,zbt-we3526|\
|
|
zbt-we826-16M|\
|
|
zbt-we826-32M|\
|
|
zbt-wg2626|\
|
|
zbt-wg3526-16M|\
|
|
zbt-wg3526-32M|\
|
|
zbt-wr8305rt)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6@eth0"
|
|
;;
|
|
gehua,ghl-r-001)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "4:wan" "6@eth0"
|
|
;;
|
|
alfa-network,awusfree1|\
|
|
alfa-network,tube-e4g|\
|
|
cs-qr10|\
|
|
d105|\
|
|
dlink,dap-1522-a1|\
|
|
dch-m225|\
|
|
ex2700|\
|
|
ex3700|\
|
|
hpm|\
|
|
mzk-ex300np|\
|
|
mzk-ex750np|\
|
|
na930|\
|
|
pbr-d1|\
|
|
ravpower,wd03|\
|
|
tama,w06|\
|
|
tplink,tl-mr3020-v3|\
|
|
tplink,tl-wr802n-v4|\
|
|
u25awf-h1|\
|
|
wli-tx4-ag300n|\
|
|
wmdr-143n|\
|
|
wmr-300|\
|
|
wn3000rpv3|\
|
|
wrh-300cr)
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
dlink,dwr-118-a1)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan:2" "2:lan:3" "3:lan:1" "4:lan:0" "5:wan" "6@eth0"
|
|
;;
|
|
dlink,dwr-118-a2)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan:2" "2:lan:1" "3:lan:3" "4:lan" "0:wan" "6@eth0"
|
|
;;
|
|
psg1218b)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:3" "1:lan:2" "2:lan:1" "3:wan" "6@eth0"
|
|
;;
|
|
whr-300hp2|\
|
|
whr-600d|\
|
|
wsr-1166|\
|
|
wsr-600)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:1" "1:lan:2" "2:lan:3" "3:lan:4" "4:wan:5" "6@eth0"
|
|
;;
|
|
ar670w|\
|
|
ar725w|\
|
|
rakwireless,rak633|\
|
|
rt-ac51u)
|
|
ucidef_add_switch "switch0" \
|
|
"0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6t@eth0"
|
|
;;
|
|
belkin,f9k1109v1|\
|
|
rt-n15|\
|
|
wl-351)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "5@eth0"
|
|
;;
|
|
asl26555-8M|\
|
|
asl26555-16M|\
|
|
rp-n53)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "6t@eth0"
|
|
;;
|
|
atp-52b|\
|
|
awm002-evb-4M|\
|
|
awm002-evb-8M|\
|
|
bdcom,wap2100-sk|\
|
|
c20i|\
|
|
dir-645|\
|
|
gl-mt300a|\
|
|
gl-mt300n|\
|
|
gl-mt750|\
|
|
hiwifi,hc5861b|\
|
|
jhr-n805r|\
|
|
jhr-n825r|\
|
|
jhr-n926r|\
|
|
mikrotik,rb750gr3|\
|
|
mikrotik,rbm33g|\
|
|
mzk-wdpr|\
|
|
rt-n14u|\
|
|
skylab,skw92a|\
|
|
tplink,c20-v4|\
|
|
tplink,c50-v3|\
|
|
tplink,c50-v4|\
|
|
tplink,tl-mr3420-v5|\
|
|
tplink,tl-wr842n-v5|\
|
|
tl-wr840n-v4|\
|
|
tl-wr840n-v5|\
|
|
tl-wr841n-v13|\
|
|
u7628-01-128M-16M|\
|
|
ubnt-erx|\
|
|
ubnt-erx-sfp|\
|
|
ur-326n4g|\
|
|
wrtnode|\
|
|
wrtnode2p | \
|
|
wrtnode2r | \
|
|
youhua,wr1200js|\
|
|
zbt-wa05|\
|
|
zyxel,keenetic-extra-ii)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6@eth0"
|
|
;;
|
|
c50|\
|
|
tplink,c20-v1)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan:3" "2:lan:4" "3:lan:1" "4:lan:2" "0:wan" "6@eth0"
|
|
;;
|
|
dir-860l-b1|\
|
|
elecom,wrc-1167ghbk2-s|\
|
|
elecom,wrc-2533gst|\
|
|
elecom,wrc-1900gst|\
|
|
hg255d|\
|
|
iodata,wn-ax1167gr|\
|
|
iodata,wn-gx300gr)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "0:wan" "6@eth0"
|
|
;;
|
|
gnubee,gb-pc1|\
|
|
gnubee,gb-pc2)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "4:lan" "6@eth0"
|
|
;;
|
|
gl-mt300n-v2)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "0:wan" "6@eth0"
|
|
;;
|
|
awapn2403)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:wan" "6@eth0"
|
|
;;
|
|
b2c|\
|
|
nw718|\
|
|
psr-680w|\
|
|
sl-r7205|\
|
|
ur-336un|\
|
|
w502u|\
|
|
wr6202)
|
|
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
|
|
;;
|
|
br-6475nd)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "9@eth0"
|
|
;;
|
|
c108|\
|
|
cf-wr800n)
|
|
ucidef_add_switch "switch0" \
|
|
"4:lan" "6t@eth0"
|
|
;;
|
|
cy-swr1100)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "9@eth0"
|
|
;;
|
|
duzun-dm06)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "0:wan" "6@eth0"
|
|
;;
|
|
e1700|\
|
|
mt7620a_mt7530)
|
|
ucidef_add_switch "switch1" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6@eth0"
|
|
;;
|
|
edimax,br-6478ac-v2|\
|
|
tplink,c2-v1)
|
|
ucidef_add_switch "switch1" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6@eth0"
|
|
;;
|
|
hc5661|\
|
|
head-weblink,hdrm200|\
|
|
y1s)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "5:lan" "0:wan" "6@eth0"
|
|
;;
|
|
hc5861)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "5:wan" "6@eth0"
|
|
;;
|
|
iodata,wn-ac1167gr|\
|
|
iodata,wn-ac733gr3)
|
|
ucidef_add_switch "switch1" \
|
|
"1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "0:wan" "6@eth0"
|
|
;;
|
|
kn_rf)
|
|
ucidef_add_switch "switch0" \
|
|
"0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6@eth0"
|
|
;;
|
|
kng_rc)
|
|
ucidef_add_switch "switch1" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "7t@eth0"
|
|
;;
|
|
mlwg2|\
|
|
wizard8800|\
|
|
wl-330n)
|
|
ucidef_set_interface_lan "eth0.1"
|
|
;;
|
|
mr200)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "6t@eth0"
|
|
ucidef_set_interface_wan "usb0"
|
|
;;
|
|
netgear,r6120)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "4:wan" "6@eth0"
|
|
;;
|
|
hc5761)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "4:lan" "0:wan" "6@eth0"
|
|
;;
|
|
mzk-dp150n|\
|
|
vocore-8M|\
|
|
vocore-16M)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "4:lan" "6t@eth0"
|
|
;;
|
|
newifi-d1)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan:2" "2:lan:1" "4:wan" "6@eth0"
|
|
;;
|
|
phicomm,k2g)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5:wan" "6@eth0"
|
|
;;
|
|
dlink,dir-510l|\
|
|
glinet,vixmini|\
|
|
netgear,ex6150|\
|
|
re350-v1)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "6@eth0"
|
|
;;
|
|
re6500)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:1" "1:lan:2" "2:lan:3" "3:lan:4" "6@eth0"
|
|
;;
|
|
rt-n56u)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "8@eth0"
|
|
;;
|
|
tew-638apb-v2)
|
|
ucidef_add_switch "switch0" \
|
|
"4:lan" "6@eth0"
|
|
;;
|
|
lava,lr-25g001|\
|
|
tew-691gr|\
|
|
tew-692gr|\
|
|
wlr-6000)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "0@eth0"
|
|
;;
|
|
tplink,tl-wr902ac-v3)
|
|
ucidef_add_switch "switch0" \
|
|
"4:lan" "6@eth0"
|
|
;;
|
|
vonets,var11n-300|\
|
|
wt1520-4M|\
|
|
wt1520-8M)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "4:wan" "6@eth0"
|
|
;;
|
|
vocore2|\
|
|
vocore2lite)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "2:lan" "6t@eth0"
|
|
;;
|
|
f5d8235-v1|\
|
|
f5d8235-v2|\
|
|
tew-714tru|\
|
|
v11st-fe|\
|
|
wzr-agl300nh)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0"
|
|
;;
|
|
wcr-1166ds)
|
|
ucidef_add_switch "switch0" \
|
|
"3:lan" "4:wan" "6@eth0"
|
|
;;
|
|
wcr-150gn|\
|
|
we1026-5g-16m)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "6t@eth0"
|
|
;;
|
|
whr-1166d)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "5:wan" "6@eth0"
|
|
;;
|
|
wizfi630a)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:wan" "6@eth0"
|
|
;;
|
|
wiznet,wizfi630s)
|
|
ucidef_add_switch "switch0" \
|
|
"0:wan" "3:lan" "4:lan" "6@eth0"
|
|
;;
|
|
wt3020-4M|\
|
|
wt3020-8M)
|
|
ucidef_add_switch "switch0" \
|
|
"4:lan" "0:wan" "6@eth0"
|
|
;;
|
|
xiaomi,mir3g)
|
|
ucidef_add_switch "switch0" \
|
|
"2:lan:2" "3:lan:1" "1:wan" "6t@eth0"
|
|
;;
|
|
xiaomi,mir3p)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan:3" "2:lan:2" "3:lan:1" "4:wan" "6@eth0"
|
|
;;
|
|
zbtlink,zbt-we1226|\
|
|
y1)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:2" "1:lan:1" "4:wan" "6@eth0"
|
|
;;
|
|
zyxel,keenetic-start)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:3" "1:lan:2" "2:lan:1" "3:lan:0" "4:wan" "6@eth0"
|
|
;;
|
|
*)
|
|
RT3X5X=`cat /proc/cpuinfo | egrep "(RT3.5|RT5350)"`
|
|
if [ -n "${RT3X5X}" ]; then
|
|
ramips_setup_rt3x5x_vlans
|
|
else
|
|
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
|
|
fi
|
|
;;
|
|
esac
|
|
}
|
|
|
|
ramips_setup_macs()
|
|
{
|
|
local board="$1"
|
|
local lan_mac=""
|
|
local wan_mac=""
|
|
|
|
case $board in
|
|
a5-v11|\
|
|
ht-tm02|\
|
|
wmdr-143n)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
;;
|
|
carambola|\
|
|
freestation5|\
|
|
w502u|\
|
|
wnce2001)
|
|
wan_mac=$(mtd_get_mac_binary factory 46)
|
|
;;
|
|
bc2|\
|
|
broadway|\
|
|
d105|\
|
|
dir-300-b7|\
|
|
dir-320-b1|\
|
|
dir-620-a1|\
|
|
esr-9753|\
|
|
freestation5|\
|
|
hlk-rm04|\
|
|
mpr-a1|\
|
|
psr-680w|\
|
|
sl-r7205|\
|
|
y1|\
|
|
y1s)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
lan_mac=$(macaddr_setbit_la "$lan_mac")
|
|
wan_mac=$(macaddr_add "$lan_mac" 1)
|
|
;;
|
|
belkin,f9k1109v1)
|
|
wan_mac=$(mtd_get_mac_ascii uboot-env HW_WAN_MAC)
|
|
lan_mac=$(mtd_get_mac_ascii uboot-env HW_LAN_MAC)
|
|
;;
|
|
br-6475nd)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
wan_mac=$(mtd_get_mac_binary devdata 7)
|
|
;;
|
|
cy-swr1100|\
|
|
dch-m225)
|
|
lan_mac=$(mtd_get_mac_ascii factory lanmac)
|
|
;;
|
|
dir-645)
|
|
lan_mac=$(mtd_get_mac_ascii nvram lanmac)
|
|
wan_mac=$(mtd_get_mac_ascii nvram wanmac)
|
|
;;
|
|
dir-860l-b1)
|
|
lan_mac=$(mtd_get_mac_ascii factory lanmac)
|
|
wan_mac=$(mtd_get_mac_ascii factory wanmac)
|
|
;;
|
|
dlink,dir-510l|\
|
|
dlink,dwr-116-a1|\
|
|
dlink,dwr-118-a1|\
|
|
dlink,dwr-118-a2|\
|
|
dlink,dwr-921-c1|\
|
|
dlink,dwr-922-e2|\
|
|
lava,lr-25g001)
|
|
wan_mac=$(jboot_config_read -m -i $(find_mtd_part "config") -o 0xE000)
|
|
lan_mac=$(macaddr_add "$wan_mac" 1)
|
|
;;
|
|
e1700)
|
|
wan_mac=$(mtd_get_mac_ascii config WAN_MAC_ADDR)
|
|
;;
|
|
edimax,br-6478ac-v2)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
wan_mac=$(macaddr_add "$lan_mac" 2)
|
|
;;
|
|
elecom,wrc-1167ghbk2-s|\
|
|
elecom,wrc-2533gst|\
|
|
elecom,wrc-1900gst|\
|
|
sk-wb8)
|
|
wan_mac=$(mtd_get_mac_binary factory 57350)
|
|
;;
|
|
gl-mt300n-v2|\
|
|
whr-g300n)
|
|
wan_mac=$(mtd_get_mac_binary factory 4)
|
|
;;
|
|
hc5*61|\
|
|
hc5661a|\
|
|
hc5962|\
|
|
hiwifi,hc5861b)
|
|
lan_mac=`mtd_get_mac_ascii bdinfo "Vfac_mac "`
|
|
[ -n "$lan_mac" ] || lan_mac=$(cat /sys/class/net/eth0/address)
|
|
wan_mac=$(macaddr_add "$lan_mac" 1)
|
|
;;
|
|
iodata,wn-ac1167gr|\
|
|
iodata,wn-ac733gr3)
|
|
wan_mac=$(macaddr_add "$(mtd_get_mac_binary Factory 4)" -1)
|
|
;;
|
|
iodata,wn-ax1167gr|\
|
|
iodata,wn-gx300gr)
|
|
wan_mac=$(macaddr_add "$(mtd_get_mac_binary Factory 4)" 1)
|
|
;;
|
|
kn_rc|\
|
|
kn_rf|\
|
|
kng_rc)
|
|
wan_mac=$(mtd_get_mac_binary factory 40)
|
|
;;
|
|
linkits7688)
|
|
wan_mac=$(mtd_get_mac_binary factory 4)
|
|
lan_mac=$(mtd_get_mac_binary factory 46)
|
|
;;
|
|
mac1200rv2)
|
|
lan_mac=$(mtd_get_mac_binary factory_info 13)
|
|
wan_mac=$(macaddr_add "$lan_mac" 1)
|
|
;;
|
|
miwifi-mini)
|
|
wan_mac=$(cat /sys/class/net/eth0/address)
|
|
lan_mac=$(macaddr_setbit_la "$wan_mac")
|
|
;;
|
|
m3|\
|
|
m4-4M|\
|
|
m4-8M|\
|
|
x5|\
|
|
x8)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
lan_mac=$(macaddr_add "$lan_mac" -2)
|
|
;;
|
|
newifi-d1)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
lan_mac=$(macaddr_add "$lan_mac" 2)
|
|
;;
|
|
omega2|\
|
|
omega2p)
|
|
wan_mac=$(mtd_get_mac_binary factory 4)
|
|
lan_mac=$(mtd_get_mac_binary factory 46)
|
|
;;
|
|
oy-0001|\
|
|
phicomm,k2g)
|
|
lan_mac=$(mtd_get_mac_binary factory 40)
|
|
wan_mac=$(mtd_get_mac_binary factory 46)
|
|
;;
|
|
r6220|\
|
|
netgear,r6350)
|
|
wan_mac=$(mtd_get_mac_binary factory 4)
|
|
lan_mac=$(macaddr_add "$wan_mac" 1)
|
|
;;
|
|
rt-n56u)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
lan_mac=$(macaddr_setbit_la "$lan_mac")
|
|
wan_mac=$(mtd_get_mac_binary factory 32772)
|
|
;;
|
|
skylab,skw92a)
|
|
lan_mac=$(mtd_get_mac_binary factory 40)
|
|
wan_mac=$(mtd_get_mac_binary factory 46)
|
|
;;
|
|
tew-691gr)
|
|
wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 4)" 3)
|
|
;;
|
|
tew-692gr)
|
|
wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 4)" 1)
|
|
;;
|
|
tiny-ac)
|
|
lan_mac=$(mtd_get_mac_ascii u-boot-env LAN_MAC_ADDR)
|
|
wan_mac=$(mtd_get_mac_ascii u-boot-env WAN_MAC_ADDR)
|
|
;;
|
|
vr500)
|
|
lan_mac=$(mtd_get_mac_binary factory 57344)
|
|
wan_mac=$(mtd_get_mac_binary factory 57350)
|
|
;;
|
|
w306r-v20)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
wan_mac=$(macaddr_add "$lan_mac" 5)
|
|
;;
|
|
wcr-1166ds|\
|
|
wsr-1166)
|
|
local index="$(find_mtd_index "board_data")"
|
|
wan_mac="$(grep -m1 mac= "/dev/mtd${index}" | cut -d= -f2)"
|
|
lan_mac=$wan_mac
|
|
;;
|
|
wcr-150gn)
|
|
wan_mac=$(mtd_get_mac_binary factory 40)
|
|
;;
|
|
whr-1166d|\
|
|
whr-300hp2|\
|
|
whr-600d|\
|
|
wsr-600)
|
|
wan_mac=$(mtd_get_mac_binary factory 4)
|
|
lan_mac=$wan_mac
|
|
;;
|
|
wizfi630a)
|
|
lan_mac=$(mtd_get_mac_binary factory 4)
|
|
wan_mac=$(mtd_get_mac_binary factory 40)
|
|
;;
|
|
wlr-6000)
|
|
wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 32772)" 2)
|
|
;;
|
|
xiaomi,mir3g|\
|
|
xiaomi,mir3p)
|
|
lan_mac=$(mtd_get_mac_binary Factory 0xe006)
|
|
;;
|
|
zyxel,keenetic-start)
|
|
wan_mac=$(mtd_get_mac_binary factory 40)
|
|
;;
|
|
*)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
wan_mac=$(macaddr_add "$lan_mac" 1)
|
|
;;
|
|
esac
|
|
|
|
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
|
|
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
|
|
}
|
|
|
|
board_config_update
|
|
board=$(board_name)
|
|
ramips_setup_interfaces $board
|
|
ramips_setup_macs $board
|
|
board_config_flush
|
|
|
|
exit 0
|