forked from Ivasoft/openwrt
07c45c0859
The Compex WPQ873 is a development board with two M.2 B-key
slots for cellular modems.
Device info:
- IPQ8072A SoC
- 512MiB RAM
- 256MiB NAND flash
- 8MiB SPI NOR
- 3x 1GigE ports
- 1x 2.5GigE port
- 2.4GHz/5GHz AX WLAN
- 1x USB 3.0 port
- 1x M.2 B-key socket with PCIe 3.0
- 1x M.2 B-key socket with PCIe 2.0 and USB 3.0
- 4x SIM card slots
- Bluetooth LE 5.0 (QCA4024)
Prerequisites
1) TFTP server
2) 3.3V USB to TTL cable for UART console
2.54mm pitch 4-pin header for UART is readily provided on board, no modifications are necessary to access it
TTL connector pinout: 2=TX, 3=RX, 4=GND
Arrow marks pin 1 which is 3.3V
Serial port settings: 115200 8N1 no flow control
The device will most likely ship with a QSDK-based firmware.
1. Power on device and interrupt u-boot to obtain u-boot CLI
2. set serverip to IP address of the TFTP server, for example:
`setenv serverip 192.168.1.10`
3. Download image from TFTP server:
`tftpboot 0x44000000 openwrt-ipq807x-generic-compex_wpq873-squashfs-factory.ubi`
4. Flash ubi image to both partitions and reset:
`sf probe
imxtract 0x44000000 ubi
nand device 0
nand erase 0x0 0x3400000
nand erase 0x3c00000 0x3400000
nand write $fileaddr 0x0 $filesize
nand write $fileaddr 0x3c00000 $filesize
reset`
Afterwards, you can use sysupgrade to flash new OpenWRT images.
Signed-off-by: Antti Nykänen <antti.nykanen@nokia.com>
51 lines
1008 B
Plaintext
51 lines
1008 B
Plaintext
#
|
|
# Copyright (c) 2015 The Linux Foundation. All rights reserved.
|
|
# Copyright (c) 2011-2015 OpenWrt.org
|
|
#
|
|
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/system.sh
|
|
|
|
ipq807x_setup_interfaces()
|
|
{
|
|
local board="$1"
|
|
|
|
case "$board" in
|
|
buffalo,wxr-5950ax12|\
|
|
dynalink,dl-wrx36|\
|
|
xiaomi,ax9000)
|
|
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
|
|
;;
|
|
edgecore,eap102)
|
|
ucidef_set_interfaces_lan_wan "lan" "wan"
|
|
;;
|
|
edimax,cax1800)
|
|
ucidef_set_interfaces_lan_wan "lan"
|
|
;;
|
|
netgear,wax218)
|
|
ucidef_set_interface_lan "lan" "dhcp"
|
|
;;
|
|
qnap,301w)
|
|
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 10g-2" "10g-1"
|
|
;;
|
|
compex,wpq873|\
|
|
redmi,ax6|\
|
|
xiaomi,ax3600)
|
|
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan"
|
|
;;
|
|
zyxel,nbg7815)
|
|
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 10g" "wan"
|
|
;;
|
|
*)
|
|
echo "Unsupported hardware. Network interfaces not initialized"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
board_config_update
|
|
board=$(board_name)
|
|
ipq807x_setup_interfaces $board
|
|
board_config_flush
|
|
|
|
exit 0
|