forked from Ivasoft/openwrt
957f9adeb1
ipTIME NAS1 is a 1-bay NAS, based on Marvell Kirkwood SoC. Specifications: * SoC: 88F6281 * RAM: 256 MiB * Flash: SPI NOR 16 MiB * SATA: 1x 3Gb/s * Ethernet: 1x 1GbE * USB: 1x 2.0 * Fan: 2 speed level * UART: JP1 (115200 8N1) * Pinout: [3V3] (TXD) (RXD) (GND) Notes: * There are several variants of the model name: "NAS-I", "NASI", "NAS1". Here "NAS1" is adopted for consistent naming scheme. * The reset button is also a USB copy button in stock FW, but in this patch the former is the only default behavior. Installation via web interface: 1. Flash sysupgrade image through the stock web interface. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
86 lines
1.7 KiB
Plaintext
86 lines
1.7 KiB
Plaintext
#
|
|
# Copyright (C) 2012-2015 OpenWrt.org
|
|
#
|
|
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/system.sh
|
|
|
|
kirkwood_setup_interfaces()
|
|
{
|
|
local board="$1"
|
|
|
|
case "$board" in
|
|
checkpoint,l-50)
|
|
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5 lan6 lan7 lan8 dmz" "eth0"
|
|
;;
|
|
cisco,on100)
|
|
ucidef_set_interface_lan "eth0 eth1"
|
|
;;
|
|
cloudengines,pogoe02|\
|
|
cloudengines,pogoplugv4|\
|
|
ctera,c200-v1|\
|
|
globalscale,sheevaplug|\
|
|
iom,iconnect-1.1|\
|
|
iom,ix2-200|\
|
|
iptime,nas1|\
|
|
netgear,readynas-duo-v2|\
|
|
raidsonic,ib-nas62x0|\
|
|
seagate,blackarmor-nas220|\
|
|
seagate,dockstar|\
|
|
seagate,goflexhome|\
|
|
seagate,goflexnet|\
|
|
zyxel,nsa310b|\
|
|
zyxel,nsa310s|\
|
|
zyxel,nsa325)
|
|
ucidef_set_interface_lan "eth0" "dhcp"
|
|
;;
|
|
endian,4i-edge-200)
|
|
ucidef_set_interface_lan "port1 port2 port3 port4 eth1"
|
|
;;
|
|
linksys,e4200-v2|\
|
|
linksys,ea3500|\
|
|
linksys,ea4500)
|
|
ucidef_set_interfaces_lan_wan "ethernet1 ethernet2 ethernet3 ethernet4" "internet"
|
|
;;
|
|
*)
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
kirkwood_setup_macs()
|
|
{
|
|
local board="$1"
|
|
local lan_mac=""
|
|
local wan_mac=""
|
|
local label_mac=""
|
|
|
|
case "$board" in
|
|
iptime,nas1)
|
|
lan_mac=$(mtd_get_mac_binary u-boot 0x3ffa8)
|
|
label_mac=$lan_mac
|
|
;;
|
|
linksys,e4200-v2|\
|
|
linksys,ea3500|\
|
|
linksys,ea4500)
|
|
wan_mac=$(mtd_get_mac_ascii u_env eth1addr)
|
|
;;
|
|
zyxel,nsa310b|\
|
|
zyxel,nsa325)
|
|
lan_mac=$(mtd_get_mac_ascii uboot_env ethaddr)
|
|
;;
|
|
esac
|
|
|
|
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
|
|
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
|
|
[ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac
|
|
}
|
|
|
|
board_config_update
|
|
board=$(board_name)
|
|
kirkwood_setup_interfaces $board
|
|
kirkwood_setup_macs $board
|
|
board_config_flush
|
|
|
|
exit 0
|