forked from Ivasoft/openwrt
13579e6441
The Netgear EVG2000 is a wifi gigabit router, 2.4 GHz single band with
two internal antennas integrated in the main PCB.
Hardware:
- SoC: Broadcom BCM6369
- CPU: dual core BMIPS4350 V3.1 @400Mhz
- RAM: 64 MB DDR
- Flash: 16 MB parallel NOR
- LAN switch: Broadcom BCM53115, 5x 1Gbit
- Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn
- USB: 2x 2.0
- Buttons: 2x, 1 reset
- LEDs: 10x
- FXS: 2x
- UART: yes
Installation via CFE web UI:
1. Power off the router and make a temporal TX-RX shortcircuit on the
serial pins.
2. Power on the router and wait 3 or more seconds
3. Remove the TX-RX shortcircuit
4. Browse to http://192.168.1.1 or http://192.168.0.1 and upload the
firmware
5. Wait a few minutes for it to finish
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
32 lines
1.0 KiB
Plaintext
32 lines
1.0 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
. /lib/functions/leds.sh
|
|
. /lib/functions/uci-defaults.sh
|
|
|
|
board_config_update
|
|
|
|
case "$(board_name)" in
|
|
netgear,dgnd3700-v1 |\
|
|
netgear,dgnd3800b)
|
|
ucidef_set_led_netdev "lan" "LAN" "green:lan" "switch.1"
|
|
ucidef_set_led_netdev "wan" "WAN" "green:wan" "wan"
|
|
ucidef_set_led_netdev "wlan0" "WIFI2G" "green:wifi2g" "phy0-ap0"
|
|
ucidef_set_led_netdev "wlan1" "WIFI5G" "blue:wifi5g" "phy1-ap0"
|
|
ucidef_set_led_usbport "usb1" "USB1" "green:usb1" "usb1-port1" "usb2-port1"
|
|
ucidef_set_led_usbport "usb2" "USB2" "green:usb2" "usb1-port2" "usb2-port2"
|
|
;;
|
|
netgear,evg2000)
|
|
ucidef_set_led_netdev "lan" "LAN" "green:lan" "switch.1"
|
|
ucidef_set_led_netdev "wan" "WAN" "green:wan" "wan"
|
|
ucidef_set_led_usbdev "usb" "USB" "green:usb" "usb1-port1" "usb2-port1" "usb1-port2" "usb2-port2"
|
|
;;
|
|
observa,vh4032n)
|
|
ucidef_set_led_usbport "usb1" "USB1" "blue:hspa" "usb1-port1" "usb2-port1"
|
|
ucidef_set_led_usbport "usb2" "USB2" "red:hspa" "1-2-port1" "1-2-port2"
|
|
;;
|
|
esac
|
|
|
|
board_config_flush
|
|
|
|
exit 0
|