SW/openwrt
2
0
Fork 0
forked from Ivasoft/openwrt
Code Pull Requests Activity

ramips: add support for I-O DATA WN-AC1167GR

Browse Source 
I-O DATA WN-AC1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7620A.

Specification:

- SoC     : MediaTek MT7620A
- RAM     : DDR2 64 MB
- Flash   : SPI-NOR 8MB
- WLAN    : 2.4/5 GHz, 2T2R
  - 2.4 GHz: MT7620A (SoC)
  - 5 GHz  : MT7612E
- Ethernet: 10/100/1000 Mbps (ext. MT7530)
- LED/key : 4x/3x (2x buttons, 1x slide-switch)
- UART    : through-hole on PCB
  - J2: TX, GND, RX, Vcc from SoC side
  - 115200n8

Flash instruction using factory image:

1. Boot WN-AC1167GR normaly
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This commit is contained in:
INAGAKI Hiroshi
2019-01-09 00:20:18 +09:00
committed by Christian Lamparter
parent dee8db441e
commit f305ce5c35
4 changed files with 258 additions and 0 deletions
Download Patch File Download Diff File Expand all files Collapse all files

4
target/linux/ramips/base-files/etc/board.d/01_leds
View File

@@ -188,6 +188,10 @@ ht-tm02)
ucidef_set_led_netdev "eth" "Ethernet" "$boardname:green:lan" "eth0"
set_wifi_led "$boardname:blue:wlan"
;;
iodata,wn-ac1167gr)
ucidef_set_led_wlan "wlan5g" "WLAN5G" "$boardname:green:wlan5g" "phy0radio"
ucidef_set_led_wlan "wlan2g" "WLAN2G" "$boardname:green:wlan2g" "phy1radio"
;;
kimax,u35wf)
set_wifi_led "$boardname:blue:wifi"
ucidef_set_led_netdev "eth" "ETH" "$boardname:green:eth" "eth0"

7
target/linux/ramips/base-files/etc/board.d/02_network
View File

@@ -319,6 +319,10 @@ ramips_setup_interfaces()
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "5:lan" "0:wan" "6@eth0"
;;
iodata,wn-ac1167gr)
ucidef_add_switch "switch1" \
"1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "0:wan" "6@eth0"
;;
kn_rf)
ucidef_add_switch "switch0" \
"0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6@eth0"
@@ -525,6 +529,9 @@ ramips_setup_macs()
[ -n "$lan_mac" ] || lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(macaddr_add "$lan_mac" 1)
;;
iodata,wn-ac1167gr)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary Factory 4)" -1)
;;
iodata,wn-ax1167gr|\
iodata,wn-gx300gr)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary Factory 4)" 1)