ramips: add support for Belkin F9K1109v1

Device specification:
- SoC: Ralink RT3883 (MIPS 74Kc) 500Mhz
- RAM: 64Mb
- Flash: 8MB (SPI-NOR)
- Ethernet: 10/100/1000 Mbps
- WLAN
	Wireless 1: SoC-integrated : 2.4/5 GHz
	Wireless 2: 2.4 GHz RT3092L
- LED: 2x USB, WAN, LAN
- Key: WPS, reset
- Serial: 4-pin header, (57600,8,N,1), 3.3V TTL,
	GND, RX, TX, V - J12 marking on board
- USB ports: 2 x USB 2.0

Flashing instructions:

Option 1 (from bootloader web)
- Hold reset button on the back of router when plugging
  in power (for at-least 10 seconds after plugged in)
- Connect to a Lan port
- Set computer IP to 10.10.10.3
- Go to http://10.10.10.123 in a web browser
- Click the Browse... Button and select the
   *squashfs.sysupgrade.bin file then click APPLY

Option 2 (from the stock admin web)
- Go to firmware upgrade
- Upload the **factory** image *initramfs.bin first
- Boot into openwrt
- From Luci web in openwrt upload the *squashfs.sysupgrade.bin

Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added v1 to the compatible identifier, added pciid for
the RT3092L, fixed pci unit-address, split out the F9K110X.dtsi
to prepare for a possible F9K1103 patch]

target/linux/ramips/base-files/etc/board.d/01_leds

@@ -60,6 +60,10 @@ bdcom,wap2100-sk|\
 hiwifi,hc5861b)
 	set_wifi_led "$boardname:green:wlan2g"
 	;;
+belkin,f9k1109v1)
+	set_usb_led "$boardname:green:usb1"
+	ucidef_set_led_netdev "lan" "lan" "$boardname:blue:wps" "eth0"
+	;;
 broadway)
 	set_wifi_led "$boardname:red:wps_active"
 	;;

target/linux/ramips/base-files/etc/board.d/02_network

@@ -199,6 +199,7 @@ ramips_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6t@eth0"
 		;;
+	belkin,f9k1109v1|\
 	rt-n15|\
 	wl-351)
 		ucidef_add_switch "switch0" \
@@ -483,6 +484,10 @@ ramips_setup_macs()
 		lan_mac=$(macaddr_setbit_la "$lan_mac")
 		wan_mac=$(macaddr_add "$lan_mac" 1)
 		;;
+	belkin,f9k1109v1)
+		wan_mac=$(mtd_get_mac_ascii uboot-env HW_WAN_MAC)
+		lan_mac=$(mtd_get_mac_ascii uboot-env HW_LAN_MAC)
+		;;
 	br-6475nd)
 		lan_mac=$(cat /sys/class/net/eth0/address)
 		wan_mac=$(mtd_get_mac_binary devdata 7)