lantiq: copy target to kernel 4.19

This just copies the files from the kernel 4.14 specific folders into the kernel 4.19 specific folder, no changes are done to the files in this commit. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-11-25 19:35:16 +01:00
parent bf21b6e44d
commit eee1b34ce6
116 changed files with 14836 additions and 0 deletions
--- a/target/linux/lantiq/files/arch/mips/boot/dts/EASY98000-base.dtsi
+++ b/target/linux/lantiq/files/arch/mips/boot/dts/EASY98000-base.dtsi
@@ -0,0 +1,110 @@
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	compatible = "lantiq,easy98000", "lantiq,falcon";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x4000000>;
+	};
+
+	easy98000-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&bootled_pins>;
+
+		LED_0 {
+			label = "easy98000:green:gpon";
+			gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+		LED_1 {
+			label = "easy98000:red:gpon";
+			gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+		LED_2 {
+			label = "easy98000:green:gpon_tx";
+			gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+		LED_3 {
+			label = "easy98000:green:gpon_rx";
+			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+		LED_4 {
+			label = "easy98000:green:voice";
+			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+		LED_5 {
+			label = "easy98000:green:status";
+			gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+	};
+};
+
+&ebu_cs1 {
+	eth0: ethernet@0000000 {
+		compatible = "davicom,dm9000";
+		device_type = "network";
+		reg = <0x0000003 0x1>, <0x0000001 0x1>;
+		reg-names = "addr", "data";
+		interrupt-parent = <&gpio1>;
+		#interrupt-cells = <2>;
+		interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+		local-mac-address = [ 00 00 00 00 00 00 ];
+	};
+
+	cpld@3c00000 {
+		compatible = "lantiq,easy98000_addon";
+		reg = <0x3c00000 0x2>;
+	};
+
+	cpld@3c0000c {
+		compatible = "lantiq,easy98000_cpld_led";
+		reg = <0x3c0000c 0x2>,  <0x3c00012 0x2>;
+	};
+};
+
+/* // enable this for second uart:
+&serial1 {
+	status = "okay";
+};*/
+
+&spi {
+	status = "okay";
+
+	eeprom@1 {
+		compatible = "atmel,at25", "atmel,at25160n";
+		reg = <2>;
+		spi-max-frequency = <1000000>;
+		spi-cpha;
+		spi-cpol;
+
+		pagesize = <32>;
+		size = <2048>;
+		address-width = <16>;
+	};
+};
+
+&i2c {
+	status = "okay";
+
+	clock-frequency = <100000>;
+
+	/* eeprom-emulation by OMU */
+	eeprom@50 {
+		compatible = "at,24c02";
+		reg = <0x50>;
+	};
+	eeprom@51 {
+		compatible = "at,24c02";
+		reg = <0x51>;
+	};
+};
+