SW/openwrt
2
0
Fork 0
forked from Ivasoft/openwrt
Code Pull Requests Activity

ramips: add support for D-Link DWR-118-A1

Browse Source 
The DWR-118-A1 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7610EN)
- 3x 10/100 Mbps Ethernet (3 LAN)
- 2x 10/100/1000 Mbps ICPlus IP1001 Ethernet PHY (1 WAN AND 1 LAN)
- 1x internal, non-detachable antenna
- 2x external, non-detachable antennas
- 1x USB 2.0
- UART (J1) header on PCB (57600 8n1)
- 7x LED (5x GPIO-controlled), 2x button
- JBOOT bootloader

Known issues:
- WIFI 5G LED not working
- flash is very slow

The status led has been assigned to the dwr-118-a1:green:internet led.
At the end of the boot it is switched off and is available for other
operation. Work correctly also during sysupgrade operation.

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This commit is contained in:
Pawel Dembicki
2018-10-24 14:06:35 +02:00
committed by Mathias Kresin
parent 40692f0fb5
commit e9a9b7d1ed
6 changed files with 215 additions and 0 deletions
Download Patch File Download Diff File Expand all files Collapse all files

5
target/linux/ramips/base-files/etc/board.d/01_leds
View File

@@ -114,6 +114,11 @@ dlink,dwr-116-a1|\
mzk-ex300np)
set_wifi_led "$boardname:green:wifi"
;;
dlink,dwr-118-a1)
ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x1f"
ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x20"
set_wifi_led "$boardname:green:wlan2g" "wlan1"
;;
dlink,dwr-118-a2)
ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x0e"
ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x01"

5
target/linux/ramips/base-files/etc/board.d/02_network
View File

@@ -162,6 +162,10 @@ ramips_setup_interfaces()
wrh-300cr)
ucidef_set_interface_lan "eth0"
;;
dlink,dwr-118-a1)
ucidef_add_switch "switch0" \
"1:lan:2" "2:lan:3" "3:lan:1" "4:lan:0" "5:wan" "6@eth0"
;;
dlink,dwr-118-a2)
ucidef_add_switch "switch0" \
"1:lan:2" "2:lan:1" "3:lan:3" "4:lan" "0:wan" "6@eth0"
@@ -475,6 +479,7 @@ ramips_setup_macs()
wan_mac=$(mtd_get_mac_ascii factory wanmac)
;;
dlink,dwr-116-a1|\
dlink,dwr-118-a1|\
dlink,dwr-118-a2|\
dlink,dwr-921-c1|\
lava,lr-25g001)