forked from Ivasoft/openwrt
ipq807x: add QNAP 301w
QNAP 301w is a AX WIFI router with 4 1G and 2 10G ports.
Specifications:
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 1024MB of DDR3
• Storage: 4GB eMMC (contains kernel and rootfs) / 8MB NOR
(contains art and u-boot-env)
• Ethernet: 4x 1G RJ45 ports + 2 10G ports (Aquantia AQR113C)
• WLAN:
2.4GHz: Qualcomm QCN5024 4x4 (40 MHz) 802.11b/g/n/ax 1174 Mbps PHY rate
5GHz: Qualcomm QCN5054 4x4 (80 MHz) or 2x2 (160 MHz) 802.11a/b/g/n/ac/ax 2402 PHY rate
• LEDs:
7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs
• Buttons: 1x soft reset / 1x WPS
• Power: 12V DC jack
A poulated serial header is onboard.
RX/TX is working, bootwait is active, secure boot is not enabled.
SSH can be activated in the stock firmware, hold WPS button til the second beep
(yes the router has a buzzer)
SSH is available on port 22200, login with user admin and
password "mac address of the router".
Installation Instructions:
• obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial)
• stop auto boot
• setenv serverip 192.168.10.1
• setenv ipaddr 192.168.10.10
• tftpboot the initramfs image
(openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb)
• bootm
• make sure that current_entry is set to "0":
"fw_printenv -n current_entry" should be print "0". If not,
do "fw_setenv current_entry 0"
• copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
to the device to /tmp folder
• sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4)
• reboot
Note: this leaves the second kernel / rootfs parition untouched. So if you want
to go back to stock, stop u-boot autoboot, "setenv current_entry 1" ,
"saveenv", "bootipq".
Stock firmware should start from the second partition.
Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt
in the first partitions
Make 10G Aquantia phy's work:
The aquantia phy's need a firmware to work. This can either be loaded
in linux with a userspace tool or in u-boot.
I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is
aq_load_fw available in u-boot. But first the right firmware needs to write
to the 0:ETHPHYFW mtd partition (it is empty on my device)
Grab the ethphy firmware image from:
https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn
and scp that to openwrt.
Check the 0:ETHPHYFW partition number:
cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10.
Backup the 0:ETHPHYFW partition:
dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place.
Write the new firmware image to the 0:ETHPHYFW partition:
"mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10".
Reboot to u-boot.
Check if aq_load_fw is working:
"aq_load_fw 0", that checks the firmware and if successfull,
loads iram and dram to one of the aquantia phy's.
If that worked, add the aq_load_fw to the bootcmd:
setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq"
"saveenv"
"reset"
Board reboots and the firmware load to both phy's should start and
then openwrt boots.
Check if the 10G ports work.
Note: lan port labeled "10G-2" is configured as WAN port as per default.
All other port are in the br-lan. This can be changed in the network config.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
This commit is contained in:
Dirk Buchwalder
committed by
Robert Marko
Robert Marko
parent
a36fc589fe
commit
bd17683261
@@ -0,0 +1,410 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/* Copyright (c) 2021, Dirk Buchwalder <buchwalder@posteo.de> */
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "ipq8074.dtsi"
|
||||
#include "ipq8074-hk-cpu.dtsi"
|
||||
#include "ipq8074-ess.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
model = "QNAP 301w";
|
||||
compatible = "qnap,301w", "qcom,ipq8074";
|
||||
|
||||
aliases {
|
||||
serial0 = &blsp1_uart5;
|
||||
/*
|
||||
* Aliases as required by u-boot
|
||||
* to patch MAC addresses
|
||||
*/
|
||||
led-boot = &led_system_red;
|
||||
led-failsafe = &led_system_red;
|
||||
led-running = &led_pwr_green;
|
||||
led-upgrade = &led_system_red;
|
||||
ethernet0 = &dp1;
|
||||
ethernet1 = &dp2;
|
||||
ethernet2 = &dp3;
|
||||
ethernet3 = &dp4;
|
||||
ethernet4 = &dp5;
|
||||
ethernet5 = &dp6_syn;
|
||||
label-mac-device = &dp1;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-0 = <&button_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
wps-button {
|
||||
label = "wps";
|
||||
gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
|
||||
reset-button {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 67 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-0 = <&leds_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
led_system_green: led-system-green {
|
||||
label = "green:system";
|
||||
gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
};
|
||||
|
||||
led_system_red: led-system-red {
|
||||
label = "red:system";
|
||||
gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
};
|
||||
|
||||
led_pwr_green: led-pwr-green {
|
||||
label = "green:pwr";
|
||||
gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
};
|
||||
|
||||
led-wifi-green {
|
||||
label = "green:wifi";
|
||||
gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
};
|
||||
|
||||
led-lan4-green {
|
||||
label = "green:lan4";
|
||||
gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
};
|
||||
|
||||
led-lan4-amber {
|
||||
label = "amber:lan4";
|
||||
gpios = <&tlmm 7 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_AMBER>;
|
||||
};
|
||||
|
||||
led-lan3-green {
|
||||
label = "green:lan3";
|
||||
gpios = <&tlmm 8 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
};
|
||||
|
||||
led-lan3-amber {
|
||||
label = "amber:lan3";
|
||||
gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_AMBER>;
|
||||
};
|
||||
|
||||
led-lan2-green {
|
||||
label = "green:lan2";
|
||||
gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
};
|
||||
|
||||
led-lan2-amber {
|
||||
label = "amber:lan2";
|
||||
gpios = <&tlmm 13 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_AMBER>;
|
||||
};
|
||||
|
||||
led-lan1-green {
|
||||
label = "green:lan1";
|
||||
gpios = <&tlmm 14 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
};
|
||||
|
||||
led-lan1-amber {
|
||||
label = "amber:lan1";
|
||||
gpios = <&tlmm 15 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_AMBER>;
|
||||
};
|
||||
|
||||
led-10g-1-green {
|
||||
label = "green:10g_1";
|
||||
gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
};
|
||||
|
||||
led-10g-1-amber {
|
||||
label = "amber:10g_1";
|
||||
gpios = <&tlmm 56 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_AMBER>;
|
||||
};
|
||||
|
||||
led-10g-2-green {
|
||||
label = "green:10g_2";
|
||||
gpios = <&tlmm 51 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
};
|
||||
|
||||
led-10g-2-amber {
|
||||
label = "amber:10g_2";
|
||||
gpios = <&tlmm 52 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_AMBER>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
|
||||
mdio_pins: mdio-state {
|
||||
mdc-pins {
|
||||
pins = "gpio68";
|
||||
function = "mdc";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mdio-pins {
|
||||
pins = "gpio69";
|
||||
function = "mdio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
button_pins: button-state {
|
||||
wps-pins {
|
||||
pins = "gpio57";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
rst-pins {
|
||||
pins = "gpio67";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
leds_pins: leds-state {
|
||||
pins = "gpio1", "gpio3", "gpio4", "gpio6", "gpio7", "gpio8",
|
||||
"gpio11", "gpio12", "gpio13", "gpio14", "gpio15", "gpio42",
|
||||
"gpio51", "gpio52", "gpio54", "gpio56";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart5 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&prng {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ssphy_0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qusb_phy_0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ssphy_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qusb_phy_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_spi1 { /* BLSP1 QUP1 */
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
cs-gpios = <0>;
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
reg = <0>;
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <50000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "qcom,smem-part";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
|
||||
|
||||
aqr113c_0: ethernet-phy@0 {
|
||||
compatible ="ethernet-phy-ieee802.3-c45";
|
||||
reg = <0>;
|
||||
reset-gpios = <&tlmm 59 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
aqr113c_8: ethernet-phy@8 {
|
||||
compatible ="ethernet-phy-ieee802.3-c45";
|
||||
reg = <8>;
|
||||
reset-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
qca8075_16: ethernet-phy@16 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <16>;
|
||||
};
|
||||
|
||||
qca8075_17: ethernet-phy@17 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <17>;
|
||||
};
|
||||
|
||||
qca8075_18: ethernet-phy@18 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <18>;
|
||||
};
|
||||
|
||||
qca8075_19: ethernet-phy@19 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <19>;
|
||||
};
|
||||
};
|
||||
|
||||
&sdhc_1 {
|
||||
status = "okay";
|
||||
|
||||
/* According to the stock dts from the QNAP gpl drop
|
||||
* the emmc has a problem with the hs400 > hs200 speed switch.
|
||||
* Therefore remove the mmc-hs400-1_8v property
|
||||
*/
|
||||
/delete-property/ mmc-hs400-1_8v;
|
||||
mmc-hs200-1_8v;
|
||||
mmc-ddr-1_8v;
|
||||
vqmmc-supply = <&l11>;
|
||||
};
|
||||
|
||||
&switch {
|
||||
status = "okay";
|
||||
|
||||
switch_cpu_bmp = <0x1>; /* cpu port bitmap */
|
||||
switch_lan_bmp = <0x3e>; /* lan port bitmap */
|
||||
switch_wan_bmp = <0xc0>; /* wan port bitmap */
|
||||
switch_mac_mode = <0xb>; /* mac mode for uniphy instance0*/
|
||||
switch_mac_mode1 = <0xd>; /* mac mode for uniphy instance1*/
|
||||
switch_mac_mode2 = <0xd>; /* mac mode for uniphy instance2*/
|
||||
bm_tick_mode = <0>; /* bm tick mode */
|
||||
tm_tick_mode = <0>; /* tm tick mode */
|
||||
|
||||
qcom,port_phyinfo {
|
||||
port@0 {
|
||||
port_id = <1>;
|
||||
phy_address = <16>;
|
||||
};
|
||||
port@1 {
|
||||
port_id = <2>;
|
||||
phy_address = <17>;
|
||||
};
|
||||
port@2 {
|
||||
port_id = <3>;
|
||||
phy_address = <18>;
|
||||
};
|
||||
port@3 {
|
||||
port_id = <4>;
|
||||
phy_address = <19>;
|
||||
};
|
||||
port@4 {
|
||||
port_id = <5>;
|
||||
phy_address = <8>;
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
ethernet-phy-ieee802.3-c45;
|
||||
};
|
||||
port@5 {
|
||||
port_id = <6>;
|
||||
phy_address = <0>;
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
ethernet-phy-ieee802.3-c45;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&edma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&dp1 {
|
||||
status = "okay";
|
||||
phy-handle = <&qca8075_16>;
|
||||
label = "lan4";
|
||||
};
|
||||
|
||||
&dp2 {
|
||||
status = "okay";
|
||||
phy-handle = <&qca8075_17>;
|
||||
label = "lan3";
|
||||
};
|
||||
|
||||
&dp3 {
|
||||
status = "okay";
|
||||
phy-handle = <&qca8075_18>;
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
&dp4 {
|
||||
status = "okay";
|
||||
phy-handle = <&qca8075_19>;
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
&dp5 {
|
||||
status = "okay";
|
||||
qcom,mactype = <1>;
|
||||
phy-handle = <&aqr113c_8>;
|
||||
label = "10g-1";
|
||||
};
|
||||
|
||||
&dp6_syn {
|
||||
status = "okay";
|
||||
phy-handle = <&aqr113c_0>;
|
||||
label = "10g-2";
|
||||
};
|
||||
|
||||
&wifi {
|
||||
status = "okay";
|
||||
|
||||
qcom,ath11k-calibration-variant = "QNAP-301w";
|
||||
};
|
||||
Reference in New Issue
Block a user