forked from Ivasoft/openwrt
ipq807x: add Edimax CAX1800
Edimax CAX1800 is a 802.11 ax dual-band AP
with PoE. AP can be ceiling or wall mount.
Specifications:
• CPU: Qualcomm IPQ8070A Quad core Cortex-A53 1.4GHz
• RAM: 512MB of DDR3
• Storage: 128MB NAND (contains rootfs) / 8MB NOR (contains art and uboot-env)
• Ethernet: 1x 1G RJ45 port (QCA8072) PoE
• WLAN:
2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
5GHz: Qualcomm QCN5054 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate
• LEDs:
3 x GPIO-controlled System-LEDs
(form one virtual RGB System-LED)
black_small_square Buttons: 1x soft reset
black_small_square Power: 12V DC jack or PoE (802.3af )
An unpopulated serial header is onboard.
RX/TX is working, bootwait is active, secure boot is not enabled.
SSH can be activated in the stock firmware, but it drops only
to a limited shell .
Installation Instructions:
black_small_square obtain serial access
black_small_square stop auto boot
black_small_square tftpboot the initramfs image (serverip is set to 192.168.99.8 in uboot)
black_small_square bootm
black_small_square copy openwrt-ipq807x-generic-edimax_cax1800-squashfs-nand-factory.ubi
to the device
black_small_square write the image to the NAND:
black_small_square cat /proc/mtd and look for rootfs partition (should be mtd0)
black_small_square ubiformat /dev/mtd0 -f -y openwrt-ipq807x-generic-edimax_cax1800-squashfs-
nand-factory.ubi
black_small_square reboot
Note: Device is not using dual partitioning (NAND contains other partitions
with different manufacture data etc.)
Draytek VigorAP 960C and Lancom LW-600 both look similar, but I haven't checked them.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
This commit is contained in:
Dirk Buchwalder
committed by
Robert Marko
Robert Marko
parent
8253cb2de5
commit
a36fc589fe
@@ -0,0 +1,322 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/* Copyright (c) 2021, Dirk Buchwalder <buchwalder@posteo.de> */
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "ipq8074-512m.dtsi"
|
||||
#include "ipq8074-ac-cpu.dtsi"
|
||||
#include "ipq8074-ess.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
model = "Edimax CAX1800";
|
||||
compatible = "edimax,cax1800", "qcom,ipq8074";
|
||||
|
||||
aliases {
|
||||
serial0 = &blsp1_uart5;
|
||||
led-boot = &led_system_red;
|
||||
led-failsafe = &led_system_red;
|
||||
led-running = &led_system_green;
|
||||
led-upgrade = &led_system_red;
|
||||
/* Aliases as required by u-boot to patch MAC addresses */
|
||||
ethernet0 = &dp5;
|
||||
label-mac-device = &dp5;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
bootargs-append = " root=/dev/ubiblock0_1";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_system_red: system-red {
|
||||
label = "red:system";
|
||||
gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_system_green: system-green {
|
||||
label = "green:system";
|
||||
gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_system_blue: system-blue {
|
||||
label = "blue:system";
|
||||
gpios = <&tlmm 27 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
mdio_pins: mdio-pins {
|
||||
mdc {
|
||||
pins = "gpio68";
|
||||
function = "mdc";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mdio {
|
||||
pins = "gpio69";
|
||||
function = "mdio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart5 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&prng {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_nand {
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
nand-bus-width = <8>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "rootfs";
|
||||
reg = <0x0000000 0x3400000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
cs-select = <0>;
|
||||
status = "ok";
|
||||
|
||||
m25p80@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
reg = <0>;
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <50000000>;
|
||||
use-default-sizes;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "0:sbl1";
|
||||
reg = <0x0 0x50000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "0:mibib";
|
||||
reg = <0x50000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "0:bootconfig";
|
||||
reg = <0x60000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
label = "0:bootconfig1";
|
||||
reg = <0x80000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@a0000 {
|
||||
label = "0:qsee";
|
||||
reg = <0xa0000 0x180000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@220000 {
|
||||
label = "0:qsee_1";
|
||||
reg = <0x220000 0x180000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3a0000 {
|
||||
label = "0:devcfg";
|
||||
reg = <0x3a0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3b0000 {
|
||||
label = "0:devcfg_1";
|
||||
reg = <0x3b0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3c0000 {
|
||||
label = "0:apdp";
|
||||
reg = <0x3c0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3d0000 {
|
||||
label = "0:apdp_1";
|
||||
reg = <0x3d0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3e0000 {
|
||||
label = "0:rpm";
|
||||
reg = <0x3e0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@420000 {
|
||||
label = "0:rpm_1";
|
||||
reg = <0x420000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@460000 {
|
||||
label = "0:cdt";
|
||||
reg = <0x460000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@470000 {
|
||||
label = "0:cdt_1";
|
||||
reg = <0x470000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@480000 {
|
||||
label = "0:appsblenv";
|
||||
reg = <0x480000 0x10000>;
|
||||
};
|
||||
|
||||
partition@490000 {
|
||||
label = "0:appsbl";
|
||||
reg = <0x490000 0xa0000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@530000 {
|
||||
label = "0:appsbl_1";
|
||||
reg = <0x530000 0xa0000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@5d0000 {
|
||||
label = "0:art";
|
||||
reg = <0x5d0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@610000 {
|
||||
label = "0:ethphyfw";
|
||||
reg = <0x610000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
|
||||
|
||||
qca8075: ethernet-phy@4 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <4>;
|
||||
};
|
||||
};
|
||||
|
||||
&switch {
|
||||
status = "okay";
|
||||
|
||||
switch_cpu_bmp = <0x1>; /* cpu port bitmap */
|
||||
switch_lan_bmp = <0x1e>; /* lan port bitmap */
|
||||
switch_wan_bmp = <0x20>; /* wan port bitmap */
|
||||
switch_mac_mode = <0x0>; /* mac mode for uniphy instance0*/
|
||||
switch_mac_mode1 = <0xff>; /* mac mode for uniphy instance1*/
|
||||
switch_mac_mode2 = <0xff>; /* mac mode for uniphy instance2*/
|
||||
bm_tick_mode = <0>; /* bm tick mode */
|
||||
tm_tick_mode = <0>; /* tm tick mode */
|
||||
|
||||
qcom,port_phyinfo {
|
||||
port@0 {
|
||||
port_id = <1>;
|
||||
phy_address = <0>;
|
||||
};
|
||||
port@1 {
|
||||
port_id = <2>;
|
||||
phy_address = <1>;
|
||||
};
|
||||
port@2 {
|
||||
port_id = <3>;
|
||||
phy_address = <2>;
|
||||
};
|
||||
port@3 {
|
||||
port_id = <4>;
|
||||
phy_address = <3>;
|
||||
};
|
||||
port@4 {
|
||||
port_id = <5>;
|
||||
phy_address = <4>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&edma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&dp5 {
|
||||
status = "okay";
|
||||
phy-handle = <&qca8075>;
|
||||
label = "lan";
|
||||
};
|
||||
|
||||
&wifi {
|
||||
status = "okay";
|
||||
|
||||
qcom,ath11k-calibration-variant = "Edimax-CAX1800";
|
||||
qcom,ath11k-fw-memory-mode = <1>;
|
||||
};
|
||||
Reference in New Issue
Block a user