ath79: add support for YunCore A770

YunCore A770 is a ceiling AC750 AP with 2 Fast Ethernet ports, PoE
(802.3at) support, based on QCA9531 + QCA9887.

Specification:

- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet (PoE 802.3at support in WAN port)
- 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA
- 1T1R 5 GHz (QCA9887), with ext. FEM (SKY85728-11)
- 2x regular LED, 1x RGB LED (all driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12 V)
- UART header on PCB

Flash instruction:

1. First, gain root access to the device, following below steps:

- Login into web gui (default password/IP: admin/192.168.188.253).
- Go to 'Advanced' -> 'Management' -> 'System' and download backup of
  configuration (bakfile.bin).
- Open the file as tar.gz archive, edit/update 'shadow' file and change
  hash of root password to something known.
- Repack the archive, rename it back to 'bakfile.bin' and use to
  restore configuration of the device.
- After that, device will reboot and can be accessed over SSH.

2. Then, install OpenWrt:

- Login over SSH and issue command:
  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
- Upload 'sysupgrade' image and install it (only if previous command
  succeeded) with command: 'sysupgrade -n -F openwrt-...'.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

target/linux/ath79/base-files/etc/board.d/01_leds

@@ -171,6 +171,10 @@ wd,mynet-wifi-rangeextender)
 	ucidef_set_led_rssi "rssimedium" "RSSIMED" "$boardname:blue:rssi-med" "wlan0" "33" "100"
 	ucidef_set_led_rssi "rssihigh" "RSSIMAX" "$boardname:blue:rssi-max" "wlan0" "66" "100"
 	;;
+yuncore,a770)
+	ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth0"
+	ucidef_set_led_switch "lan" "LAN" "$boardname:green:lan" "switch0" "0x10"
+	;;
 esac
 
 board_config_flush

target/linux/ath79/base-files/etc/board.d/02_network

@@ -100,7 +100,8 @@ ath79_setup_interfaces()
 	glinet,gl-x750|\
 	tplink,tl-wr810n-v1|\
 	tplink,tl-wr810n-v2|\
-	ubnt,routerstation)
+	ubnt,routerstation|\
+	yuncore,a770)
 		ucidef_set_interfaces_lan_wan "eth1" "eth0"
 		;;
 	glinet,gl-ar750s)

target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata

@@ -150,6 +150,9 @@ case "$FIRMWARE" in
 	ubnt,unifiac-pro)
 		ath10kcal_extract "EEPROM" 20480 2116
 		;;
+	yuncore,a770)
+		ath10kcal_extract "art" 20480 2116
+		;;
 	esac
 	;;
 "ath10k/pre-cal-pci-0000:00:00.0.bin")