SW/openwrt
2
0
Fork 0
forked from Ivasoft/openwrt
Code Pull Requests Activity

ath79: add support for ALFA Network N2Q

Browse Source 
ALFA Network N2Q is an outdoor N300 AP/CPE based on Qualcomm/Atheros
QCA9531 v2. This model is a successor of the old N2 which was based
on Atheros AR7240. FCC ID: 2AB8795311.

Specifications:

- Qualcomm/Atheros QCA9531 v2
- 650/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2T2R 2.4 GHz Wi-Fi with ext. PA (Skyworks SE2623L) and LNA
- 2x 10/100 Mbps Ethernet with passive PoE input in one port (24 V)
- PoE pass through in second port (controlled by GPIO)
- support for optional 802.3af/at PoE module
- 1x mini PCIe slot (PCIe bus, extra 4.2 V for high power cards)
- 2x IPEX/U.FL connectors on PCB
- 1x USB 2.0 mini Type-B (power controlled by GPIO)
- 8x LED (7 of them are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, enabled by default)
- UART (4-pin, 2.54 mm pitch) header on PCB
- LEDs (2x 5-pin, 2.54 mm pitch) header on PCB

Flash instruction:

You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
   device, wait for first blink of all LEDs (indicates network setup),
   then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This commit is contained in:
Piotr Dymacz
2020-09-18 18:55:23 +02:00
parent 9181b039f3
commit 6492ea7d9e
6 changed files with 283 additions and 128 deletions
Download Patch File Download Diff File Expand all files Collapse all files

8
target/linux/ath79/generic/base-files/etc/board.d/01_leds
View File

@@ -17,6 +17,14 @@ alfa-network,ap121fe|\
avm,fritz450e)
ucidef_set_led_netdev "lan" "LAN" "$boardname:green:lan" "eth0"
;;
alfa-network,n2q)
ucidef_set_led_netdev "lan2" "LAN2" "$boardname:orange:lan2" "eth1"
ucidef_set_led_switch "lan1" "LAN1" "$boardname:orange:lan1" "switch0" "0x10"
ucidef_set_rssimon "wlan0" "200000" "1"
ucidef_set_led_rssi "signal1" "SIGNAL1" "$boardname:red:signal1" "wlan0" "1" "100"
ucidef_set_led_rssi "signal2" "SIGNAL2" "$boardname:orange:signal2" "wlan0" "33" "100"
ucidef_set_led_rssi "signal3" "SIGNAL3" "$boardname:green:signal3" "wlan0" "66" "100"
;;
alfa-network,r36a)
ucidef_set_led_netdev "lan" "LAN" "$boardname:blue:lan" "eth0"
ucidef_set_led_switch "wan" "WAN" "$boardname:blue:wan" "switch0" "0x10"

12
target/linux/ath79/generic/base-files/etc/board.d/02_network
View File

@@ -78,6 +78,12 @@ ath79_setup_interfaces()
alfa-network,ap121fe)
ucidef_set_interface_lan "eth0 usb0"
;;
alfa-network,n2q|\
devolo,dvl1200e|\
devolo,dvl1750e|\
ocedo,ursus)
ucidef_set_interface_lan "eth0 eth1"
;;
avm,fritz4020|\
pcs,cr3000|\
tplink,archer-c58-v1|\
@@ -147,11 +153,6 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0@eth0" "3:lan" "2:wan"
;;
devolo,dvl1200e|\
devolo,dvl1750e|\
ocedo,ursus)
ucidef_set_interface_lan "eth0 eth1"
;;
devolo,magic-2-wifi)
ucidef_add_switch "switch0" \
"0@eth0" "2:wan" "3:lan" "4:lan"
@@ -402,6 +403,7 @@ ath79_setup_macs()
;;
alfa-network,ap121f|\
alfa-network,ap121fe|\
alfa-network,n2q|\
alfa-network,r36a|\
engenius,ens202ext-v1)
label_mac=$(mtd_get_mac_binary art 0x1002)