SW/openwrt
2
0
Fork 0
forked from Ivasoft/openwrt
Code Pull Requests Activity

ath79: add support for NEC Aterm WG1200CR

Browse Source 
NEC Aterm WG1200CR is a 2.4/5 GHz band 11ac router,
based on Qualcomm Atheros QCA9563.

Specification:

- SoC		: Qualcomm Atheros QCA9563
- RAM		: DDR2 128 MiB
- Flash		: SPI-NOR 8 MiB
- WLAN		: 2.4/5 GHz 2T2R
  - 2.4 GHz	: QCA9563 (SoC)
  - 5 GHz	: QCA9888
- Ethernet	: 2x 10/100/1000 Mbps
  - Switch	: QCA8334
- LEDs/Input	: 12x/4x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - JP1: Vcc, GND, NC, TX, RX from power connector side
  - 115200 bps

Flash instruction using factory image:

1. Boot WG1200CR normaly
2. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Known issues:

- cannot be controlled LEDs other than Power (Green/Red)
  - only Power LEDs are connected to SoC GPIO; other LEDs
    connected to the gpiochip on ath10k chip (QCA9888)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [commit
message formatting]
This commit is contained in:
INAGAKI Hiroshi
2019-03-16 13:27:32 +09:00
committed by Christian Lamparter
parent fac27643f0
commit 643fcfc8d6
5 changed files with 219 additions and 7 deletions
Download Patch File Download Diff File Expand all files Collapse all files

16
target/linux/ath79/base-files/etc/board.d/02_network
View File

@@ -128,6 +128,13 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0@eth0" "5:wan" "6@eth1" "4:lan"
;;
nec,wg1200cr|\
ubnt,nanostation-ac|\
ubnt,unifiac-mesh-pro|\
ubnt,unifiac-pro)
ucidef_add_switch "switch0" \
"0@eth0" "2:lan" "3:wan"
;;
nec,wg800hp)
ucidef_add_switch "switch0" \
"0@eth0" "2:lan" "3:lan" "4:lan" "1:wan"
@@ -234,12 +241,6 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0@eth0" "5:lan" "1:wan"
;;
ubnt,nanostation-ac|\
ubnt,unifiac-mesh-pro|\
ubnt,unifiac-pro)
ucidef_add_switch "switch0" \
"0@eth0" "2:lan" "3:wan"
;;
xiaomi,mi-router-4q)
ucidef_set_interface_wan "eth0"
ucidef_add_switch "switch0" \
@@ -272,7 +273,8 @@ ath79_setup_macs()
lan_mac=$(mtd_get_mac_text "mac" 4)
wan_mac=$(mtd_get_mac_text "mac" 24)
;;
dlink,dir-859-a1)
dlink,dir-859-a1|\
nec,wg1200cr)
lan_mac=$(mtd_get_mac_ascii devdata "lanmac")
wan_mac=$(mtd_get_mac_ascii devdata "wanmac")
;;

4
target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
View File

@@ -117,6 +117,10 @@ case "$FIRMWARE" in
ath9k_eeprom_extract "art" 4096 1088
ath9k_patch_fw_mac $(mtd_get_mac_ascii u-boot-env ethaddr) 2
;;
nec,wg1200cr)
ath9k_eeprom_extract "art" 4096 1088
ath9k_patch_fw_mac $(mtd_get_mac_ascii devdata wlan24mac) 2
;;
nec,wg800hp)
ath9k_eeprom_extract "art" 4096 1088
ath9k_patch_fw_mac $(mtd_get_mac_text board_data 1664) 2

6
target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
View File

@@ -163,6 +163,12 @@ case "$FIRMWARE" in
;;
"ath10k/pre-cal-pci-0000:00:00.0.bin")
case $board in
nec,wg1200cr)
ath10kcal_extract "art" 20480 12064
ath10kcal_patch_mac_crc $(mtd_get_mac_ascii devdata wlan5mac)
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
phicomm,k2t)
ath10kcal_extract "art" 20480 12064
ath10kcal_patch_mac_crc $(k2t_get_mac "5g_mac")