forked from Ivasoft/openwrt
ar71xx: Add support for Teltonika RUT900
Teltonika RUT900 is a Router with LTE dual SIM, WiFi, 4x Ethernet ports, I/O, RS232, RS485, GPS. The device ist based on a Atheros AR9344 rev 3, Specifications: - 560/450/225 MHz (CPU/DDR/AHB) - 128 MB of RAM - 16 MB of FLASH - Serial Console header on a Card Board edge connector - 4x 10/100 Mbps Ethernet (3x LAN, 1x WAN) - 2.4 GHz Wifi - 2x external, detachable Wifi antennas - LTE Modem Huawei ME909u-521 (Also other Modem seen) - 2x LTE antennas - 1x GPS antenna - 7x LED, 1x button - 1x USB Connector - 1x Serial RS232 - 1x Serial RS485 - 1x MicroSD Card The GPL sources of the device are available at www.teltonika.lt/gpl/ and are based on OpenWRT Barrier Breaker (14.07) Running from tftp: The Router starts into the uboot Webupdater if the Button ist pressed more than 3 seconds, if no Network cable is attached it starts the uboot serial console, from there the router loads the firmware image via tftpboot from 192.168.1.2:firmware.bin (the router has the 192.168.1.1). With bootm the loaded image will be booted. Signed-off-by: Steffen Weinreich <steve@weinreich.org>
This commit is contained in:
Steffen Weinreich
committed by
John Crispin
John Crispin
parent
ec987e59c4
commit
224e5f5efa
@@ -2021,3 +2021,14 @@ config ATH79_MACH_TL_WPA8630
|
||||
select ATH79_DEV_LEDS_GPIO
|
||||
select ATH79_DEV_M25P80
|
||||
select ATH79_DEV_WMAC
|
||||
|
||||
config ATH79_MACH_TLT_RUT900
|
||||
bool "Teltonika RUT900 board support"
|
||||
select SOC_AR934X
|
||||
select ATH79_DEV_AP9X_PCI if PCI
|
||||
select ATH79_DEV_ETH
|
||||
select ATH79_DEV_GPIO_BUTTONS
|
||||
select ATH79_DEV_LEDS_GPIO
|
||||
select ATH79_DEV_M25P80
|
||||
select ATH79_DEV_USB
|
||||
select ATH79_DEV_WMAC
|
||||
|
||||
@@ -212,6 +212,7 @@ obj-$(CONFIG_ATH79_MACH_TL_WR841N_V9) += mach-tl-wr841n-v9.o
|
||||
obj-$(CONFIG_ATH79_MACH_TL_WR941ND) += mach-tl-wr941nd.o
|
||||
obj-$(CONFIG_ATH79_MACH_TL_WR941ND_V6) += mach-tl-wr941nd-v6.o
|
||||
obj-$(CONFIG_ATH79_MACH_TL_WR940N_V4) += mach-tl-wr940n-v4.o
|
||||
obj-$(CONFIG_ATH79_MACH_TLT_RUT900) += mach-tlt-rut900.o
|
||||
obj-$(CONFIG_ATH79_MACH_TUBE2H) += mach-tube2h.o
|
||||
obj-$(CONFIG_ATH79_MACH_UBNT) += mach-ubnt.o
|
||||
obj-$(CONFIG_ATH79_MACH_UBNT_UNIFIAC) += mach-ubnt-unifiac.o
|
||||
|
||||
260
target/linux/ar71xx/files/arch/mips/ath79/mach-tlt-rut900.c
Normal file
260
target/linux/ar71xx/files/arch/mips/ath79/mach-tlt-rut900.c
Normal file
@@ -0,0 +1,260 @@
|
||||
/*
|
||||
* TELTONIKA TLT-RUT900 board support
|
||||
*
|
||||
* Copyright (C) 2014 Teltonika
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify it
|
||||
* under the terms of the GNU General Public License version 2 as published
|
||||
* by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
#include <linux/phy.h>
|
||||
#include <linux/gpio.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/ath9k_platform.h>
|
||||
#include <linux/ar8216_platform.h>
|
||||
#include <linux/mmc/host.h>
|
||||
#include <linux/spi/spi.h>
|
||||
#include <linux/spi/mmc_spi.h>
|
||||
|
||||
#include <asm/mach-ath79/ar71xx_regs.h>
|
||||
|
||||
#include "common.h"
|
||||
#include "dev-eth.h"
|
||||
#include "dev-gpio-buttons.h"
|
||||
#include "dev-leds-gpio.h"
|
||||
#include "dev-m25p80.h"
|
||||
#include "dev-spi.h"
|
||||
#include "dev-usb.h"
|
||||
#include "dev-wmac.h"
|
||||
#include "machtypes.h"
|
||||
|
||||
#include <linux/i2c.h>
|
||||
#include <linux/i2c-algo-bit.h>
|
||||
#include <linux/i2c-gpio.h>
|
||||
|
||||
/* I2C interface */
|
||||
#define rut900_GPIO_SDA 17
|
||||
#define rut900_GPIO_SCK 16
|
||||
|
||||
#define RUT900_GPIO_LED_BAR0 48
|
||||
#define RUT900_GPIO_LED_BAR1 49
|
||||
#define RUT900_GPIO_LED_BAR2 50
|
||||
#define RUT900_GPIO_LED_BAR3 51
|
||||
#define RUT900_GPIO_LED_BAR4 52
|
||||
#define RUT900_GPIO_LED_ST_GRE 54
|
||||
#define RUT900_GPIO_LED_ST_RED 53
|
||||
//#define RUT900_GPIO_LED_WAN 18
|
||||
#define RUT900_GPIO_LED_LAN1 14
|
||||
#define RUT900_GPIO_LED_LAN2 13
|
||||
#define RUT900_GPIO_LED_LAN3 22
|
||||
#define RUT900_GPIO_LED_WAN 1
|
||||
|
||||
#define RUT900_GPIO_EXTERNAL_LNA0 2
|
||||
//#define RUT900_GPIO_EXTERNAL_LNA1 3
|
||||
|
||||
#define RUT900_GPIO_BTN_RESET 15
|
||||
#define RUT900_GPIO_BTN_EXPANDER 4
|
||||
#define RUT900_GPIO_BTN_TEST 58
|
||||
#define RUT900_GPIO_MMC_CS 3
|
||||
|
||||
//#define RUT900_GPIO_EXPANDER_POWER 11
|
||||
|
||||
#define RUT900_KEYS_POLL_INTERVAL 20 /* msecs */
|
||||
#define RUT900_KEYS_DEBOUNCE_INTERVAL (3 * RUT900_KEYS_POLL_INTERVAL)
|
||||
#define RUT900_KEYS_DEBOUNCE_INTERVAL_DIN 20
|
||||
|
||||
#define RUT900_MAC0_OFFSET 0
|
||||
#define RUT900_MAC1_OFFSET 6
|
||||
#define RUT900_WMAC_CALDATA_OFFSET 0x1000
|
||||
#define RUT900_PCIE_CALDATA_OFFSET 0x5000
|
||||
|
||||
static struct i2c_gpio_platform_data rut900_i2c_device_platdata = {
|
||||
.sda_pin = rut900_GPIO_SDA,
|
||||
.scl_pin = rut900_GPIO_SCK,
|
||||
.udelay = 10,
|
||||
};
|
||||
|
||||
static struct platform_device rut900_i2c_device = {
|
||||
.name = "i2c-gpio",
|
||||
.id = 0,
|
||||
.num_resources = 0,
|
||||
.resource = NULL,
|
||||
.dev = {
|
||||
.platform_data = &rut900_i2c_device_platdata,
|
||||
},
|
||||
};
|
||||
|
||||
static struct i2c_board_info rut900_i2c_devs[] __initdata = {
|
||||
{
|
||||
I2C_BOARD_INFO("pca9539", 0x74),
|
||||
},
|
||||
{
|
||||
I2C_BOARD_INFO("mcp3221", 0x4D),
|
||||
},
|
||||
};
|
||||
|
||||
static void rut900_i2c_init(void)
|
||||
{
|
||||
/* The gpio interface */
|
||||
platform_device_register(&rut900_i2c_device);
|
||||
/* I2C devices */
|
||||
i2c_register_board_info(0, rut900_i2c_devs, ARRAY_SIZE(rut900_i2c_devs));
|
||||
}
|
||||
|
||||
//Flash partitions are calcutated in drivers/mtd/tltpart.c
|
||||
static const char *rut900_part_probes[] = {
|
||||
"tlt",
|
||||
NULL,
|
||||
};
|
||||
|
||||
static struct flash_platform_data rut900_flash_data = {
|
||||
.part_probes = rut900_part_probes,
|
||||
};
|
||||
|
||||
static struct gpio_led rut900_leds_gpio[] __initdata = {
|
||||
{
|
||||
.name = "tlt:green:signal_bar0",
|
||||
.gpio = RUT900_GPIO_LED_BAR0,
|
||||
.active_low = 0,
|
||||
},
|
||||
{
|
||||
.name = "tlt:green:signal_bar1",
|
||||
.gpio = RUT900_GPIO_LED_BAR1,
|
||||
.active_low = 0,
|
||||
},
|
||||
{
|
||||
.name = "tlt:green:signal_bar2",
|
||||
.gpio = RUT900_GPIO_LED_BAR2,
|
||||
.active_low = 0,
|
||||
},
|
||||
{
|
||||
.name = "tlt:green:signal_bar3",
|
||||
.gpio = RUT900_GPIO_LED_BAR3,
|
||||
.active_low = 0,
|
||||
},
|
||||
{
|
||||
.name = "tlt:green:signal_bar4",
|
||||
.gpio = RUT900_GPIO_LED_BAR4,
|
||||
.active_low = 0,
|
||||
},
|
||||
{
|
||||
.name = "tlt:green:status",
|
||||
.gpio = RUT900_GPIO_LED_ST_GRE,
|
||||
.active_low = 0,
|
||||
},
|
||||
{
|
||||
.name = "tlt:red:status",
|
||||
.gpio = RUT900_GPIO_LED_ST_RED,
|
||||
.active_low = 0,
|
||||
},
|
||||
|
||||
};
|
||||
|
||||
static struct gpio_keys_button rut900_gpio_keys[] __initdata = {
|
||||
{
|
||||
.desc = "Reset button",
|
||||
.type = EV_KEY,
|
||||
.code = KEY_RESTART,
|
||||
.debounce_interval = RUT900_KEYS_DEBOUNCE_INTERVAL,
|
||||
.gpio = RUT900_GPIO_BTN_RESET,
|
||||
.active_low = 1,
|
||||
},
|
||||
{
|
||||
.desc = "Expander interrupt",
|
||||
.type = EV_KEY,
|
||||
.code = KEY_RFKILL,
|
||||
.debounce_interval = RUT900_KEYS_DEBOUNCE_INTERVAL_DIN,
|
||||
.gpio = RUT900_GPIO_BTN_EXPANDER,
|
||||
},
|
||||
};
|
||||
|
||||
static struct spi_board_info ath79_spi_info[] = {
|
||||
{
|
||||
.bus_num = 0,
|
||||
.chip_select = 0,
|
||||
.max_speed_hz = 25000000,
|
||||
.modalias = "m25p80",
|
||||
.platform_data = &rut900_flash_data,
|
||||
},
|
||||
{
|
||||
.bus_num = 0,
|
||||
.chip_select = 1,
|
||||
.max_speed_hz = 25000000,
|
||||
.modalias = "mmc_spi",
|
||||
}
|
||||
};
|
||||
|
||||
static struct ath79_spi_platform_data ath79_spi_data = {
|
||||
.bus_num = 0,
|
||||
.num_chipselect = 2,
|
||||
};
|
||||
|
||||
static void __init rut900_setup(void)
|
||||
{
|
||||
u8 *mac = (u8 *) KSEG1ADDR(0x1f020000);
|
||||
u8 *art = (u8 *) KSEG1ADDR(0x1f030000);
|
||||
u8 tmpmac[ETH_ALEN];
|
||||
|
||||
ath79_register_spi(&ath79_spi_data, ath79_spi_info, 2);
|
||||
ath79_register_leds_gpio(-1, ARRAY_SIZE(rut900_leds_gpio),
|
||||
rut900_leds_gpio);
|
||||
ath79_register_gpio_keys_polled(-1, RUT900_KEYS_POLL_INTERVAL,
|
||||
ARRAY_SIZE(rut900_gpio_keys),
|
||||
rut900_gpio_keys);
|
||||
|
||||
ath79_wmac_set_ext_lna_gpio(0, RUT900_GPIO_EXTERNAL_LNA0);
|
||||
|
||||
ath79_init_mac(tmpmac, mac, 2);
|
||||
ath79_register_wmac(art + RUT900_WMAC_CALDATA_OFFSET, tmpmac);
|
||||
|
||||
|
||||
ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_SW_ONLY_MODE);
|
||||
|
||||
ath79_register_mdio(1, 0x0);
|
||||
|
||||
/* LAN */
|
||||
ath79_init_mac(ath79_eth1_data.mac_addr, mac, 0);
|
||||
|
||||
/* GMAC1 is connected to the internal switch */
|
||||
ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
|
||||
|
||||
ath79_register_eth(1);
|
||||
|
||||
/* WAN */
|
||||
ath79_init_mac(ath79_eth0_data.mac_addr, mac, 1);
|
||||
|
||||
/* GMAC0 is connected to the PHY4 of the internal switch */
|
||||
ath79_switch_data.phy4_mii_en = 1;
|
||||
ath79_switch_data.phy_poll_mask = BIT(4);
|
||||
ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
|
||||
ath79_eth0_data.phy_mask = BIT(4);
|
||||
ath79_eth0_data.mii_bus_dev = &ath79_mdio1_device.dev;
|
||||
|
||||
ath79_register_eth(0);
|
||||
|
||||
ath79_register_usb();
|
||||
|
||||
ath79_gpio_output_select(RUT900_GPIO_LED_LAN1,
|
||||
AR934X_GPIO_OUT_LED_LINK3);
|
||||
ath79_gpio_output_select(RUT900_GPIO_LED_LAN2,
|
||||
AR934X_GPIO_OUT_LED_LINK2);
|
||||
ath79_gpio_output_select(RUT900_GPIO_LED_LAN3,
|
||||
AR934X_GPIO_OUT_LED_LINK1);
|
||||
ath79_gpio_output_select(RUT900_GPIO_LED_WAN,
|
||||
AR934X_GPIO_OUT_LED_LINK4);
|
||||
|
||||
//SPI CS1
|
||||
ath79_gpio_output_select(RUT900_GPIO_MMC_CS,
|
||||
7);
|
||||
|
||||
//HS UART
|
||||
ath79_gpio_output_select(18, 79);
|
||||
|
||||
/* Init I2C interface */
|
||||
rut900_i2c_init();
|
||||
}
|
||||
|
||||
MIPS_MACHINE(ATH79_MACH_TLT_RUT900, "TLT-RUT900",
|
||||
"TELTONIKA TLT-RUT900",
|
||||
rut900_setup);
|
||||
@@ -259,6 +259,7 @@ enum ath79_mach_type {
|
||||
ATH79_MACH_TL_WR941ND_V5, /* TP-LINK TL-WR941ND v5 */
|
||||
ATH79_MACH_TL_WR941ND_V6, /* TP-LINK TL-WR941ND v6 */
|
||||
ATH79_MACH_TL_WR940N_V4, /* TP-LINK TL-WR940N v4 */
|
||||
ATH79_MACH_TLT_RUT900, /* Teltonika RUT900 */
|
||||
ATH79_MACH_TUBE2H, /* Alfa Network Tube2H */
|
||||
ATH79_MACH_UBNT_AIRGW, /* Ubiquiti AirGateway */
|
||||
ATH79_MACH_UBNT_AIRGWP, /* Ubiquiti AirGateway Pro */
|
||||
|
||||
Reference in New Issue
Block a user