ramips: add support for YunCore FAP690

It is an in-wall 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A.

Specifications:
- SoC: MT7621AT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 16 MB SPI NOR
- Wi-Fi:
    - MT7915DN + MT7905DAN: 2.4/5 GHz
- Ethernet: 1x 1GiE via MT7530
- UART: J4 (115200 baud)
    - Pinout: [3V3] (TXD) (RXD) (GND)

- Bootloader: U-Boot
- Buttons:
    - SW1 - no label on the box, combined with led
- Led: Status. RGB controlled by
    - GPIO 14 - green color
    - GPIO 15 - red color
    - GPIO 16 - blue color

Installation:
OEM firmware is based on LEDE with custom UI and support standard sysupgrade
variant of firmware. However it requires "*.ubin" extension for sysupgrade file.
Always select "Factory reset" switch on upgrade to OpenWRT, otherwise
it will not boot.

MAC addresses as verified by OEM firmware:
vendor   source
LAN      factory 0x4 (label)
5g       factory 0x4 (label)
2g       label with flipped bits bit in 1-st byte and bits 5, 6, 7 in
	4-th byte

Example
label:  44:xx:xx:b7:xx:xx
lan:    44:xx:xx:b7:xx:xx
2g      46:xx:xx:c7:xx:xx
5g      44:xx:xx:b7:xx:xx

Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>

target/linux/ramips/mt7621/base-files/etc/board.d/01_leds

@@ -170,6 +170,9 @@ xiaomi,redmi-router-ac2100)
 youhua,wr1200js)
 	ucidef_set_led_netdev "internet" "INTERNET" "green:wan" "wan"
 	;;
+yuncore,fap690)
+	ucidef_set_led_netdev "eth_link" "LAN link" "blue:status" "lan" "link"
+	;;
 yuncore,ax820)
 	ucidef_set_led_netdev "lan" "LAN" "green:lan" "lan"
 	ucidef_set_led_netdev "wan" "WAN" "green:wan" "wan"

target/linux/ramips/mt7621/base-files/etc/board.d/02_network

@@ -24,6 +24,7 @@ ramips_setup_interfaces()
 	ubnt,unifi-6-lite|\
 	ubnt,unifi-flexhd|\
 	ubnt,unifi-nanohd|\
+	yuncore,fap690|\
 	zyxel,nwa50ax|\
 	zyxel,nwa55axe)
 		ucidef_set_interface_lan "lan"

target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac

@@ -126,7 +126,8 @@ case "$board" in
 		[ "$PHYNBR" = "1" ] && \
 			macaddr_setbit_la "$(mtd_get_mac_binary Factory 0xe000)" > /sys${DEVPATH}/macaddress
 		;;
-	yuncore,fap640)
+	yuncore,fap640|\
+	yuncore,fap690)
 		hw_mac_addr="$(mtd_get_mac_binary Factory 0x4)"
 		[ "$PHYNBR" = "0" ] && macaddr_setbit_la "$hw_mac_addr" > /sys${DEVPATH}/macaddress
 		[ "$PHYNBR" = "1" ] && echo -n "$hw_mac_addr" > /sys${DEVPATH}/macaddress